Impact of dimensions of the compensating mass of the automatic balancer on its acceleration
Guntis Strautmanis^{1} , Mareks Mezitis^{2} , Valentina Strautmane^{3} , Alexander Gorbenko^{4}
^{1, 2}Riga Technical University, Riga, Latvija
^{3}Riga Technical University, Daugavpils, Latvija
^{4}Kerch State Maritime Technological University, Kerch, Russia
^{1}Corresponding author
Vibroengineering PROCEDIA, Vol. 12, 2017, p. 15.
https://doi.org/10.21595/vp.2017.18449
Received 9 April 2017; accepted 10 April 2017; published 30 June 2017
JVE Conferences
The constructions of balltype automatic balancing devices with a ballshaped crosssection in the body are widely known. The specificity of such automatic balancers is the presence of several stable regimes of movement of compensating masses, though the choice of the dimensions of compensating masses and how it influences the operation of an automatic balancer have not been completely clarified issues yet. The given article is devoted to the clarification of the influence of dimensions of compensating masses on working conditions of the automatic balancer.
Keywords: automatic balancer, working regime, ball, rotor, torusshaped body.
1. Introduction
The body of the automatic balancer is a torus with a circular raceway in the crosssection of the body [1, 2]. The body of the automatic balancer is fastened concentrically in relation to the rotor axis and at its rotation the compensating masses together with the rotor start to move in circumferential and crosssectional directions. The acceleration of the compensating masses till the rotor velocity occurs if initial conditions [3] are provided.
There are works [1] which specify that if it is not possible to ensure initial conditions for the compensating masses, they will steadily move inside in relation to the torusshaped body (unsteady regime of the operation of an automatic balancer) and cause increased vibrations of the rotor. Therefore, this is of interest to determine the impact of dimensions of a compensating mass on the operation of the automatic balancing device.
The purpose of work is to determine necessary initial conditions for a compensating mass to ensure its acceleration till the rotor velocity (stop of the compensating mass in relation to the torusshaped body of the automatic balancer). This work continues the set of works [1] and is based on experimental researches of a centrifugal machine [4] and a separator [5].
2. Calculation scheme and mathematical model of a rotor with an automatic balancer
The authors of work consider a symmetric vertical rigid rotor on the elastic dissipative suspender and with an automatic balancer fixed symmetrically in relation to the supports. The parameters of the calculation scheme of the rotor system are marked as follows:
$R$ – radius of the torusshaped body of the automatic balancer on the average circumference in the circumferential direction;
${R}_{1}$ – radius of the torusshaped body of the automatic balancer in the crosssection;
$r$ – radius of the compensating mass (ballshaped body);
$m$ – mass of the ballshaped body (the compensating mass);
${m}_{r}$ – rotor mass;
$e$ – static unbalance of the rotor;
$c$ and $b$ – coefficients of rigidity and viscous damping corresponding to the elastic suspender of the rotor. The body of the automatic balancer is concentrically fixed on the rotor and rotates together with it with angular velocity $\omega $.
The calculation scheme of the rotor with an automatic balancer is displayed in Fig. 1. In relation to the fixed system of coordinates $0xyz$ the rotor together with the body of the automatic balancer makes planeparallel movement circumscribed by the movement of the rotor axis (coordinates $x$, $y$). Movement of the compensating mass is circumscribed by two angle coordinates in the flexible system of coordinates $0{x}_{1}{y}_{1}{z}_{1}$ (coordinates $\psi $, $\alpha $).
Fig. 1. Calculation scheme of the rotor with the automatic balancer
The set of differential equations of movement describing the movement of the rotor system with an automatic balancer is given in [1]:
where ${f}_{1}$,..., ${f}_{5}$ – functions depending on the parameters of the rotor system [1]; $B$ – coefficient depending on the geometric parameters of the automatic balancer; $N$ – a unit force of the safe pressure of the compensating mass on the inner surface of the body of the automatic balancer.
Taking into account that the velocity of the rotor’s rotation is constant ($\dot{\phi}=\omega =\mathrm{c}\mathrm{o}\mathrm{n}\mathrm{s}\mathrm{t}$, $\phi =\omega t$), and for the convenience of a numerical solution of the set of equations [1] we will present it in a dimensionless aspect, having expressed the system parameters through the following values:
$\frac{{R}_{1}r}{e}={e}_{0},\frac{{R}_{1}}{e}={e}_{1},\frac{R}{e}={e}_{2},\frac{k}{r}={k}_{r},{g}_{0}=\frac{\mathrm{9,81}}{e{\omega}^{2}},$
where $\tau $ – dimensionless time. At the numerical solution of the differential equations we will accept $e=$ 1 and $\omega =$ 1.
The dimensionless force of safe pressure of the compensating mass on the inner surface of the body of the automatic balancer:
The results of the calculation of the set of differential equations are received in the form of dimensionless velocities and coordinates:
3. Research results of the mathematical model
The differential equations of movement Eqs. (14) of the rotor system with an automatic balancer were researched with the help of software SPRING [6] which provides a possibility to carry out calculations, both at the working, and at a transient regime of the automatic balancer.
The authors research the influence of the diameter of the compensating mass on the conditions of its acceleration till the rotor velocity. The initial velocity of the compensating mass in the circumferential direction of the body of the automatic balancer was thus defined ${v}_{3}=\dot{\psi}/\omega $ (at $\tau =$ 0, ${x}_{1}=$ 0, ${v}_{1}=$ 0, ${x}_{2}=$ 0, ${v}_{2}=$ 0, ${x}_{3}=$ 0, ${v}_{4}=$ 0, ${x}_{4}=$ 0) at which its acceleration till the working velocity of the rotor is ensured. The calculation results are given in Table 1. The graphic display of dependence of initial velocity of the compensating mass in the circumferential direction of the automatic balancer ${v}_{3}$ on the value relating to the space between the body of the automatic balancer and the compensating mass ${e}_{0}$ at various values of the coefficient of rolling friction $k$ is given in Fig. 2. The change of the rolling friction is taken within the range: $k=$ 10^{5},…, 3·10^{5} m (for a frictionless bearing along hard steel). From Fig. 2 it is clear that the acceleration of the compensating mass is essentially influenced by its dimensions and the coefficient of rolling friction.
Table 1. The calculation results
The coefficient of rolling friction $k=$ 3·10^{5} m


${e}_{0}$

0.25

0.50

1.00

2.00

2.50

2.60

2.70


${v}_{3}$

–0.356

–0.382

–0.421

–0.523

–0.600

–0.640

1.000


The coefficient of rolling friction $k=$ 2·10^{5} m


${e}_{0}$

3.00

4.00

5.00

6.00

6.50

6.70

6.75

6.80

${v}_{3}$

–0.102

–0.211

–0.322

–0.452

–0.540

–0.605

–0.637

–1.000

The coefficient of rolling friction $k=$ 10^{5} m


${e}_{0}$

8.80

9.00

10.00

10.50

10.60

10.75

10.83

10.90

${v}_{3}$

–0.001

–0.069

–0.303

–0.438

–0.470

–0.529

–0.580

–1.000

Fig. 2. Dependence of initial velocity of the compensating mass in the circumferential direction of the body of the automatic balancer ${v}_{3}$ on the value relating to the space between the body of the automatic balancer and the compensating mass ${e}_{0}$ at the change of the coefficient of rolling friction $k$
In case of invariable dimensions of the automatic balancing device ($R$ and ${R}_{1}$) and value of rotor unbalance e it is necessary to ensure quite certain dimensions of the compensating mass $r$. At the reduction of the coefficient of rolling friction for the acceleration of the compensating mass till the rotor velocity it is necessary to reduce the dimensions of the compensating mass (to increase the space between the compensating mass and the body of the automatic balancer).
On the other hand, at the increase of dimensions of the compensating mass (space reduction between the compensating mass and the body of the automatic balancer), it is necessary to increase the coefficient of rolling friction. At the same time, at greater values of the coefficient of rolling friction the amplitudes of rotor oscillations increase. Fig. 3 displays the amplitudes of rotor oscillations at various values of rolling friction and the following parameters of the rotor systems: $n=$ 0.357; $p=$ 0.005; ${m}_{0}=$ 0.005; ${e}_{0}=$ 2.5; ${e}_{1}=$ 15; ${e}_{2}=$ 200. Two values of the rolling friction thus have been taken: in the first case $k$ = 10^{5} m, and in the second one $k=$ 3·10^{5} m.
Dependence of amplitudes of rotor oscillations towards the axis $x$ on the value of the coefficient of rolling friction between the compensating mass and the body of the automatic balancer is shown in Fig. 4. The amplitudes of oscillation towards axis y change in the same way. Fig. 4 displays that at the increase of the coefficient of rolling friction the amplitudes of rotor oscillation also increase.
The reason to increase the amplitudes of rotor oscillations is that at the increase of the coefficient of rolling friction because of the increased force of resistance the compensating mass stops further from an optimum place, which can be seen in Fig. 5.
The practical confirmation of the research results is received in [2] where for the acceleration of the compensating masses till the rotor velocity a ball of a smaller diameter was placed in the automatic balancer.
Fig. 3. 1 – amplitudes of rotor oscillations at $k=$ 10^{5} m
Fig. 4. Dependence of amplitudes of rotor 2 – amplitudes of rotor oscillations at $k=$ 3·10^{5} m oscillations towards axis $x$ on the value of the coefficient of rolling friction ${k}_{r}=k/r$
Fig. 5. The coordinate of the compensating mass in the circumferential direction ${x}_{3}$ depending on the value of the relative coefficient of rolling friction ${k}_{r}=k/r$
4. Conclusions
As a result of the carried calculations of the mathematical model of a vertical rotor with concentrically fixed body of the torusshaped automatic balancer with a circular crosssection on it, it has been found that the acceleration of the compensating mass of the automatic balancer till working velocity of the rotor essentially depends on the dimensions of the compensating mass and the coefficient of rolling friction. Thus, the smaller the dimensions of the compensating mass are (the bigger the space between the body of the automatic balancer and the compensating mass is), the smaller coefficient of rolling friction can be applied to implement the acceleration of the compensating mass. Otherwise, the compensating mass will steadily move inside the body of the automatic balancer, and the rotor axis will oscillate with heightened amplitudes.
References
 Strautmanis G., Mezitis M., Strautmane V. Model of vertical rotor with a balltype automatic balancer. Vibroengineering Procedia, Vol. 8, 2016, p. 5762. [Search CrossRef]
 Olausson Stefan, Hagglund Anders, Wierzba Paul Cost Effective and Reliable Automatic Balancer for High Speed Applications. Patent 2002/0056338 A1 US, Appl. No. 60/216,152, 2002. [Search CrossRef]
 Strautmanis G., Grinevich I., Strautmane V. The influence of automatic equalizer and rotor parameters on the ball’s motion mode. Mehatronic Systems and Materials 2014: Selected Papers, Opole University of Tehnology, Poland, Opole, 2015, p. 135141. [Search CrossRef]
 Strautmanis G., Jurjevs V., Cokalo V. Veļas mazgājamo mašīnu centrifūgu balansēšanas ierīce. LV Patents, LV 14368 B, 2011. [Search CrossRef]
 Gorbenko A. N., Radchenko O. P. Some outcomes of vibration experimental exploration of ship centrifugal separator with balls autobalancing device. Aerospace Technique and Technology (Kharkov), Vol. 42, Issue 7, 2003, p. 158160, (in Russian). [Search CrossRef]
 Ščukins I., Zakrževskis M., Ivanov Y., et al. Application of software SPRING and method of complete bifurcation groups for the bifurcation analysis of nonlinear dynamical system. Journal of Vibroengineering, Vol. 10, Issue 4, 2008, p. 510518. [Search CrossRef]
Cited By
Herald of the Bauman Moscow State Technical University. Series Mechanical Engineering
A.N. Gorbenko, S.Kh. Shmelev, G. Strautmanis

2019

Procedia Computer Science
Alexander Gorbenko, Mareks Mezitis, Valentina Strautmane, Guntis Strautmanis

2019
